BSD Portscomms/py-elelabs-zigbee-ezsp-utility 20220218 FreeBSD
Elelabs Firmware Update Utility
- System
- FreeBSD
- Repository
- FreeBSD ports
- Maintainer
- [email protected]
- License
- APACHE20
- Categories
- comms, python
- Package size
- 582.5 KiB, 1467.3 KiB installed
Description
The Elelabs Firmware Update Utility is a basic Python 3 script to flash the firmware inside a range of Elelabs Zigbee and Thread products to a newer version.
Currently sold supported products based on Silicon Labs microcontrollers: Elelabs Zigbee Raspberry Pi Shield ELR023 (EFR32MG13P) Elelabs Zigbee USB Adapter ELU013 (EFR32MG13P)
Previously sold supported products based on Silicon Labs microcontrollers: Elelabs Zigbee Raspberry Pi Shield ELR022 (EFR32MG1B) Elelabs Zigbee USB Adapter ELU012 (EFR32MG1B) Elelabs Zigbee Raspberry Pi Shield EZBPIS (EM357) Elelabs Zigbee USB Adapter EZBUSBA (EM357)
Disclaimer: This utility should also work with other generic EZSP (EmberZNet Serial Protocol) or Spinel (Openthread Serial Protocol) based adapters and modules from other vendors, however firmwares for products not from Elelabs are not provided here and there is no guarantees that it will work with non-Elelabs products. Be wanted that you may void your warranty and even brick your adapter if the firmware update is not supported by your mnaufacturer.
In the other systems
| System | Port | Version |
|---|---|---|
| FreeBSD | comms/py-elelabs-zigbee-ezsp-utility | 20220218 |
| DragonFly | comms/py-elelabs-zigbee-ezsp-utility | 20220218 |
| HardenedBSD | comms/py-elelabs-zigbee-ezsp-utility | 20220218 |
| GhostBSD | comms/py-elelabs-zigbee-ezsp-utility | 20220218 |
Install
Binary package:
pkg install py312-elelabs-zigbee-ezsp-utilityFrom the ports tree:
cd /usr/ports/comms/py-elelabs-zigbee-ezsp-utility/ && make install cleanTo depend on this port in another port's Makefile:
RUN_DEPENDS= py312-elelabs-zigbee-ezsp-utility>0:comms/py-elelabs-zigbee-ezsp-utilityPackages
The version each package repository carries. “-” means the repository builds no package of it, “n/a” that there is no such repository.
| Repository | aarch64 | amd64 | armv6 | armv7 | i386 |
|---|---|---|---|---|---|
| FreeBSD:14:latest | 20220218 | 20220218 | 20220218 | 20220218 | 20220218 |
| FreeBSD:14:quarterly | 20220218 | 20220218 | n/a | 20220218 | 20220218 |
| FreeBSD:15:latest | 20220218 | 20220218 | n/a | 20220218 | 20220218 |
| FreeBSD:15:quarterly | 20220218 | 20220218 | n/a | n/a | n/a |
| FreeBSD:16:latest | 20220218 | 20220218 | n/a | n/a | n/a |
| FreeBSD:16:quarterly | n/a | n/a | n/a | n/a | n/a |
Dependencies
As this port's Makefile names them.
Runtime 2
${PYTHON_PKGNAMEPREFIX}pyserial>=3.4: comms/py-pyserial${PYTHON_PKGNAMEPREFIX}xmodem>=0.4.5: comms/py-xmodem
The full lists below include those, and their dependencies in turn.
Build dependencies 7
Run dependencies 9
No port depends on this one.
Configuration
No options to configure.
- USES
- python shebangfix
- Service scripts
- none
Message after installing
!!! ATTENTION !!!
Make sure that you are flashing proper F/W.
There is different pinout in different images and you may loose
connection to EFR32 chip after flashing.
Extra F/W sources:
https://www.zigbee2mqtt.io/guide/adapters/
https://github.com/xsp1989/zigbeeFirmware/
https://github.com/grobasoz/zigbee-firmware
https://github.com/zha-ng/EZSP-Firmware
https://github.com/MattWestb/EFR32-FW
https://github.com/walthowd/husbzb-firmware
Please note if you are using the EZSP v8 firmware you will also have to
add the following to your configuration.yaml for the Home Assistant
ZHA integration to load successfully.
zha:
zigpy_config:
ezsp_config:
CONFIG_PACKET_BUFFER_COUNT: 64
CONFIG_MAX_END_DEVICE_CHILDREN: 32
CONFIG_SOURCE_ROUTE_TABLE_SIZE: 200
Files
distinfo 1
| File | Size | SHA256 |
|---|---|---|
| Elelabs-elelabs-zigbee-ezsp-utility-20220218-7fc415497f7e2b3410e3350b359ac5c71043399e_GH0.tar.gz | 1.244999e+06 | 412f7c5b0b7786c8a6d6f760a3063d4c0e0551d79bd023a731e7200c69324158 |
Commit history 0
No commits in the history this site was built from.