comms/py-elelabs-zigbee-ezsp-utility 20220218 DragonFly

Elelabs Firmware Update Utility

System: DragonFly
Repository: DPorts
Maintainer: [email protected] (as in FreeBSD)
License: APACHE20
Categories: comms, python
Package size: 518.9 KiB, 1467.3 KiB installed

Description

The Elelabs Firmware Update Utility is a basic Python 3 script to flash the the firmware inside a range of Elelabs Zigbee and Thread products to a newer version.

Currently sold supported products based on Silicon Labs microcontrollers: Elelabs Zigbee Raspberry Pi Shield ELR023 (EFR32MG13P) Elelabs Zigbee USB Adapter ELU013 (EFR32MG13P)

Previously sold supported products based on Silicon Labs microcontrollers: Elelabs Zigbee Raspberry Pi Shield ELR022 (EFR32MG1B) Elelabs Zigbee USB Adapter ELU012 (EFR32MG1B) Elelabs Zigbee Raspberry Pi Shield EZBPIS (EM357) Elelabs Zigbee USB Adapter EZBUSBA (EM357)

Disclaimer: This utility should also work with other generic EZSP (EmberZNet Serial Protocol) or Spinel (Openthread Serial Protocol) based adapters and modules from other vendors, however firmwares for products not from Elelabs are not provided here and there is no guarantees that it will work with non-Elelabs products. Be wanted that you may void your warranty and even brick your adapter if the firmware update is not supported by your mnaufacturer.

In the other systems

The newest version among them is 20220218, as upstream numbers it.

System

Port

Version

Vulnerabilities

Status

Maintainer

Last update

DragonFly

comms/py-elelabs-zigbee-ezsp-utility

20220218 newest

none known

[email protected]

FreeBSD

comms/py-elelabs-zigbee-ezsp-utility

20220218 newest

none known

[email protected]

HardenedBSD

comms/py-elelabs-zigbee-ezsp-utility

20220218 newest

no data

[email protected]

GhostBSD

comms/py-elelabs-zigbee-ezsp-utility

20220218 newest

no data

[email protected]

Install

Binary package:

pkg install py311-elelabs-zigbee-ezsp-utility

From DPorts:

cd /usr/dports/comms/py-elelabs-zigbee-ezsp-utility && make install clean

Dependency graph

Ports that need it on the left, what it needs to run on the right; at most 8 of each. "Dependencies" below lists them all.

graph LR
  me["comms/py-elelabs-zigbee-ezsp-utility"]
  me --> d0["comms/py-pyserial"]
  me --> d1["comms/py-xmodem"]
  me --> d2["lang/python311"]
  classDef this fill:#ab2b28,color:#ffffff,stroke:#ab2b28
  class me this

Dependencies

Run dependencies 3

No port depends on this one.

Configuration

No options to configure.

Service scripts: none

Message after installing

!!! ATTENTION !!!

Make sure that you are flashing proper F/W.
There is different pinout in different images and you may loose
connection to EFR32 chip after flashing.


Extra F/W sources:
https://www.zigbee2mqtt.io/guide/adapters/
https://github.com/xsp1989/zigbeeFirmware/
https://github.com/grobasoz/zigbee-firmware
https://github.com/zha-ng/EZSP-Firmware
https://github.com/MattWestb/EFR32-FW
https://github.com/walthowd/husbzb-firmware


Please note if you are using the EZSP v8 firmware you will also have to
add the following to your configuration.yaml for the Home Assistant
ZHA integration to load successfully.

zha:
  zigpy_config:
    ezsp_config:
      CONFIG_PACKET_BUFFER_COUNT: 64
      CONFIG_MAX_END_DEVICE_CHILDREN: 32
      CONFIG_SOURCE_ROUTE_TABLE_SIZE: 200